The busbar processing machine has five processing units of shearing, punching, large bending and small bending. , Aluminum row for cutting, punching (round hole, waist hole), folding flat bending, vertical bending, embossing, flattening, twisting twist, pressing cable joints and other different processing.
The rusting of the busbar processing machine not only affects the appearance of the machine, but also affects the normal use. So how should the busbar processing machine be rust-proof? Let me introduce to you below.
5. Keep the oil clean and the oil circuit unobstructed, and add lubricating oil to the moving parts of each unit every shift. The electrical and hydraulic components ensure flexible movement and correct position. If abnormal phenomena are found, stop the machine immediately for inspection. After the busbar processing machine is used, the power must be disconnected after the switch is turned off. This is very important and easily overlooked. If the power is not cut off, once there is a problem, it will not be worth the loss.
1. The busbar processing machine should be used indoors as much as possible, adhere to the indoor monotony, and do a good job of waterproofing, and must not be exposed to the wind and the sun in the open air.
3. The bending unit adopts a closed overall frame structure and horizontal processing, which makes it more uniform and safer and more convenient for processing flat bending and embossing, which greatly improves the repeated positioning accuracy in mass production and prolongs the use of life.
2. Try to avoid rainy days, or reduce the use of busbar processing machines in wet seasons, and keep the indoor monotony and not be affected by rain. If conditions permit, you can cover it with a waterproof cover.
In the design of the tool shape, there are generally edge tools and oblique edge tools. When punching and shearing with an ordinary cutting edge tool, the entire cutting edge plane is in contact with the sheet material at the same time, so when punching large or thick plate workpieces, the punching force is often large. If the cutting edge plane of the tool is made to be inclined at an angle to the horizontal plane, the cutting edge will not cut in at the same time during punching and shearing, but will punch the material gradually, which is equivalent to reducing the shearing section area, thus reducing the punching force and reducing the punching force. Reduce the impact on the tool, so this design uses a beveled edge tool.
How to prevent the CNC bus processing machine from rusting and aging, when the customer fails to do a good job of rust prevention, and the CNC bus processing machine rusts, we indicate that it is also appropriate. It not only seriously affects the CNC busbar processing machine, but also affects the normal use of customers. The following are some good ways to prevent the rust and rot of the CNC bus processing machine.
3. Regularly check whether the busbar processing machine appears to be rusted, and clean it up in time. To prevent problems before they happen, do a good job in the more important work of rust prevention of busbar processing machines.
3. Single pump station busbar processing machine: one hydraulic pump station supplies three processing units of punching, shearing and folding, and the three processing units work in sequence.
The above are some ways about the rust prevention of busbar processing machines, I hope they can help you. If you have any questions or needs about the busbar processing machine, you can contact us at any time!
After any mechanical equipment has been used for a long time, there will be a lot of dust and product debris attached to it, and the busbar processing machine is no exception. If it is not cleaned in time, it may affect the normal use of the busbar processing machine. Therefore, for the busbar processing machine, in addition to the maintenance work, the cleaning work is also more important. So how should the busbar processing machine be cleaned? Let me introduce to you below.
1. Hot oil cleaning method. The bearing hardened with soft dry oil or anti-rust paste should be immersed in hot oil at 100-200 ℃, clamp the bearing with pliers, and use a brush to clean the oil on the bearing. Soft dry oil or anti-rust paste is heated to 100-200 ℃ to melt, and it is very easy to wash out from the gap of the bearing. Sometimes as long as the bearing is repeatedly shaken in the oil, the oil will flow away from the gap.
When cleaning the old busbar processing machine motor or the radial spherical bearing of the imported motor, the balls, the ball carrier and the inner ring should be rotated laterally from the outer ring and then immersed in hot oil. The short cylindrical roller bearing should also be cleaned when cleaning. The rollers, ball carrier, inner and outer rings should be disengaged. During hot oil cleaning, the temperature of the oil should not exceed 20°C. If direct heating with an open flame, attention should be paid to avoid burning the oil. The bearing should be suspended in the oil pan and sinking to the bottom will cause overheating and reduce hardness.
2. General cleaning method. Soak the bearing in kerosene for 5-10 minutes, hold the inner ring with one hand, and turn the outer ring with the other hand, the dry oil or anti-rust paste on the bearing will fall off. Then put the busbar processing machine bearing into relatively clean kerosene, rinse it with a fine and soft brush, clean the oil stains in the ball and the gap, and then put it in gasoline to clean it once, take it out and put it on clean paper . When cleaning radial spherical ball bearings and short cylindrical roller bearings, the balls, the ball carrier, the inner ring and the outer ring should be separated and cleaned. The cleaning of the bearings installed on the shaft of the busbar processing machine mainly depends on the method of spraying oil or spraying with an oil gun. For the oil that is simply cleaned, first use kerosene and then gasoline; for the oil that is difficult to clean, use 100-200 ℃ first. Hot oil rinse or oil gun spray, then gasoline cleaning. We must pay attention not to scratch the bearing with sharp objects: hard grease or rust, to avoid damage to the smoothness of the bearing rolling body and groove ring, and dry the cleaned bearing with a clean cloth.