Common Types Of Busbar Processing Machines

The temperature data of the multifunctional busbar processing machine can be transmitted to the measuring instrument at a low potential through infrared light waves or radio waves. Since there may be several measurement points, for the convenience of control, the measured data has an address identification code. The disadvantage of infrared data transmission is that light wave transmission requires no obstacles in the space, and the transmission distance is short, generally only 3m~5m. It is designed with an integrated bag for copper chips and a chip outlet with an open mouth. The slide type can collect the cut and worn copper chips, so that it will not be scattered everywhere and messy. The overall shape is bright in color, the surface is painted, and it is treated with phosphoric acid skin mold for anti-rust treatment, which is wear-resistant and impact-resistant. The board seat can be directly adjusted by hand, and it can be used for long and short size standards and unified control specifications. The azimuth valve control switch accurately guides the correct use of punching machines, bending tools and cutting tools. Safe and firm foot switch, which can control the oil inlet and return. The control system and the controlled object can be researched and manufactured separately, but must be dealt with as a whole to study its dynamics at high speed, as well as the time delay effect of optical and electrical signals under ultra-high-speed motion control conditions. eliminate the problem. In the case of high speed, it is necessary to study the overall linkage that integrates the numerical control system and the control object, nonlinear control strategies based on the overall dynamic point, and intelligent control methods. The bending unit adopts horizontal processing, which is safer and more convenient during processing. The three working stations of the machine can work at the same time without affecting each other, which greatly improves the working efficiency. The working stroke of each processing unit can be easily adjusted, reducing the auxiliary processing time and improving the production efficiency. Phosphating treatment is adopted, so that the hydraulic oil will not deteriorate after long-term use. Installation, debugging (matching the mold, adjusting the blade gap) or dismantling the mold must be carried out by personnel familiar with the machine in accordance with the prescribed procedures. When the machine is working normally, do not put your hand or part of your body between the upper and lower molds (blade) to avoid All sundries and tools should not be placed on the workbench in case of an accident, so as to avoid accidents caused by rolling into the mold or knife edge. Since the machine can be operated by many people, there must be a special person responsible for directing the production according to the copper bar (or aluminum bar). Choose the thickness of the shear blade and die and the radius of the bending fillet. Be sure to stop the machine when changing the die to avoid danger. During operation, you must be careful when holding the workpiece and waiting for the slider to go down. Regularly check the sharpness of the blade and die. If the cutting edge is found to be blunt, it should be repaired or replaced in time. When the multi-functional busbar processing machine uses steel pipe as the hanger of lamps, the inner diameter of the steel pipe should not be less than 10 mm, and the thickness of the steel pipe wall should not be less than 1.5 mm; for lamps installed in rows in the same room or place, the deviation of the center line should not be greater than 5 mm ; Three-phase transformer selection of suitable transformer winding machine equipment is the key to the production of high-performance transformers, foil coil winding machine is the key equipment for winding low-voltage foil coils. Tension control and foil tape correction are the key technologies of foil coil winding machines. The tension of the foil tape of the existing domestic or imported foil coil winding machine is generated by mechanical friction, and the tension is not stable enough, which will cause uneven tightness of the wound coils, inconsistent DC resistance between coils, and outer diameter of the coil. Poor and other defects. The larger the capacity of the transformer currently used, the greater the impact on the power grid, and its safety is required to be higher and higher. The manufacturing quality of the transformer requires not only reliable electrical performance, but also more reliable mechanical stability and short-circuit resistance. The stability is mainly manifested in the control of the manufacturing process of the coil, that is, the electromagnetic balance of the high and low voltage coils is required, and the axial turns are close and evenly distributed. Therefore, the coil winding process is required to be compressed in the axial direction and in the radial direction. The vertical winding machine is used to take advantage of the self-weight of the wire cake, and the axial direction is naturally compressed, and the radial tension device is used to control the tension.